Drivetech 4x4 Rival Underbody Protection Bash Plates suitable for Triton MQ 2015 on
Drivetech 4x4 Rival Underbody Protection Bash Plates suitable for Triton MQ 2015 on
4x4 Vehicles Underbody Protection Kits or usually more commonly referred as Bash Plates or Underguards are specific solutions designed to protect the underside of your 4wd vehicle from anything that could potentially damage it such as rocks, stumps, ruts and ground strike.
These Underbody armour Kits depending on your vehicle specs will offer more robust protection to your Steering, Front, Sump, Transmission, Transfer Case, and 4wd actuator compared to standard factory protection.
if you do a lot of tough off-road driving trips then you know just how important underbody protection is and how the underside of your four-wheel drive is so vulnerable from potential hazards such as a punctured sump, a tail-shaft jammed with logs, or even a damaged radiator that can leave you stranded in remote, hard to reach locations.
These bash plates kits get specifically designed to maximize underbody protection while maintaining clearances and are an essential part of every 4×4 set up for offroad adventures.
Drivetech 4x4 Underbody Armour Protection Kits are high-quality plates made from deep stamped 6mm alloy.
These kits are suitable for Mitsubishi Triton MQ from 2015 on and are the perfect solutions for 4wd owners researching high strength solutions that are stylish, lightweight and easy to install with no drills
Features:
- Alloy construction
- Deep Stamped bash plates with stiffening ribs
- Powder Coated Finish
- Rubber Mounting pads for tight fitment and noise reduction
- Easy install by using existing bolt holes
- Inspection holes for service and maintenance
Benefits:
- Three times lighter than traditional steel plates
- Twice as durable as flat skid plates thanks to stiffening ribs
- 100% corrosion resistant with bars and brackets covered with AkzoNobel paint which protects them from corrosion
- Tight Fitment with reduced noise or vibration while driving with rubber shock absorbers, providing a tight fitting
- No drilling required for installation by using existing vehicle bolt holes and all fasteners are provided with the kits
- No need to remove for service and maintenance
- a design featuring minimal influence to ground clearance
Features and Benefits:
Video Review:
Fitment:
ITEM SPECIFICS
| Brand: | Drivetech 4x4 |
| Manufacturer Part Number: | DT-UBA19 |
| Our Part Number: | NGDT-UBA19 |
| Condition: | New |
ADDITIONAL INFORMATION
- All Four x 4 Spares are an independent supplier of aftermarket, original equipment, and genuine parts. We are in no way related to genuine or original part manufacturers, distributors, or dealers. The warranty of any OEM genuine part is solely provided by All Four x 4 Spares
- This is an aftermarket product. Equivalent original equipment part number(s) are provided for reference purposes only.
All Four x 4 Spares will always undertake to provide adequate packaging to prevent damage to products during shipping. Our responsibility for any damage to freight ends when order has left our premises. We will consider replacement of damaged product however judgement will be at our discretion. If damage has occurred during shipping it would be advised to notify us and relevant courier.
- All exchanges / credits / refunds must be returned in saleable condition with packaging, accompanied by the original invoice for proof of purchase.
- All USED mechanical parts sold carry a 3 Month parts only warranty unless otherwise specified.
- All NEW mechanical parts sold carry a 12 Month / Unlimited kilometre parts only warranty unless otherwise specified.
- All electrical parts or components sold carry a 30 Day parts only warranty unless otherwise specified.
- All Four x 4 Warranty does not cover - Labour expenses, freight or towing costs, oil leaks, broken gears, consequential damage, loss of income or any other loss or expense.
- All Four x 4 will not be liable for any repairs or work carried out, without prior approval from All Four x 4.
- Warranty is void if parts have been tampered with, modified or dismantled.
- Goods cannot be returned if they have been specially ordered or vehicle cut section.
- Goods not required must be returned within 14 Days of invoice date at purchaser’s expense. Goods will be accepted only at the Management’s discretion. If accepted for return, such goods will be subject to a 15% handling charge.
- Good will not be accepted for return if they have been fitted, unless proven faulty.
- Warranty is void for components used in performance / modified vehicles or parts / competition / off road / race applications.
- All fitment information is for vehicles released in Australia, unless specified otherwise.